REMOTE UPLOAD & DOWNLOAD (OPTION 11) [Apt19/1/95ISS1] REMOTE.TXT 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � CPU CARD � � 旼컴컴컴컴컴컴컴� � � 쿝AM 같같같같같개 � MIDNIGHT ROUTINE � 낡같같같같같같같�------------�---------------------------------� � 낡같같같같같같같� � LD 43 REQ = UPS | � 낡같같같같같같같�------------�----------------------------� | � 낡같같같같같같같� � LD 43 REQ = EDD NBK | | � 낡같같같같같같같�------------�-----------------------� | | � 낡같같같같같같같� � LD 43 REQ = EDD | | | � 낡같같같같같같같�------------�------------------� | | | � 읕컴컴컴컴컴컴컴� � | | | | � � | | | | � � | | | | � � | | | | � � | | | | � � | | | | � � | | | | � � | | | | 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 | | | | | | | | | | | | �---------------------------| | | | | | | | |      LABEL: EDD EDD EDD UPS EDD 旼컴컴컴컴컴컴컴컴커 旼컴컴컴컴컴컴컴컴커 쿞CORE 같같같같같같� 쿎ARTRIDGE 같같같같� 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 낡같같같같같같같같개 읕컴컴컴컴컴컴컴컴켸 읕컴컴컴컴컴컴컴컴켸   | | | | 께께께께께께께께께께 SDI PORT >= 16.90 S/W = TTY 0 | | | >= 20.xx S/W = TTY 0,1 or 2.(OPTION 11E) | | | 께께께께께께께께께께 BT2 BOX (USUALLY 2400 BAUD) | | | =============================== | | | 께께께께께께께께께께 MODEM (USUALLY 2400 BAUD) | | | | | | 께께께께께께께께께께 PC COMMS PORT | | | | |  XRT XVR XBK (LD 43 REMOTE COMMANDS) 旼컴컴컴컴컴컴컴컴커 쿛C � OPTION 11 DATABASE TRANSFERRED TO & FROM PC � � USING "XMODEM" FILE TRANSFER PROTOCOL. � � � � XRT = RESTORE (UP LOAD) � � XVR = VERIFY (UP LOAD) 읕컴컴컴컴컴컴컴컴켸 XBK = BACKUP (DOWNLOAD) 栢 Procedures required to upload a configuration from a PC file to a new Option 11 via modem connection. 1. Connect a modem to COM1 or COM2 port of PC. 2. Using PROCOMM PLUS, set terminal speed to 2400,N,8,1,COM1 or COM2. Check that terminal emulation is set to VT100.Test modem is connected by typing "AT켸",a response of "OK" should be received from the modem. 3. Dial RACE telephone No. by typing "ATDTxxxxxxxxxx�" (xxxxxxxxxx = RACE telephone No. of site). When the BT2 BOX answers the call the message "CONNECT 2400" will be displayed on the terminal,respond by typing "^T켸^P" (^= Ctrl key), a response of "BT2>" or similar should be received form the BT2 BOX. 4. Type "S" to check the System Port Status which should read:- 같같같같같같같같같같같같같같같같같같같같같같� BT2 V4.3.1A UK Date: Day DD/MM/YY Time: HH:MM Port DSR Baud P D S Eol Record Reject SwName 1 X 1200 N 8 1 0D 00000 00000 Contacts 00000 00000 Modem 1200 00000 Total: 00000 00000 Pbxid: 00000000 Memory Threshold: 00% Transparency Escape Character: 00 Modem: CCITT V.22 Compatible Dialout: 같같같같같같같같같같같같같같같같같같같같같같� NOTE. � BT2 s/w Levels of below V4.2.1A UK will not support remote upload & download of Option 11 database. � PC Terminal & modem,& the BT2 BOX modem & port baud rates should all match for successful upload & download.(usually 1200 baud). � Ignoring :- DSR,Record,Reject,SwName,Contacts,Total:,Pbxid:,Memory Threshold:,& Dialout:, If any of the parameters are different from the above example they will need to be changed. � DSR (Data set ready) will display an "X" if the Option 11 TTY port is connected to the BT2 BOX,if not a display of "O" will be seen. To change any of the above parameters, type "X" to Set Extended Options,then type in a valid alternative value to the prompts dis- played.To step through a prompt leaving the value unchanged press "spacebar".When the prompt "Reboot?:" is displayed type "Y^T켸^P" to except changes & commit them to memory or "켸" to discard changes & return to "BT2>" prompt. NOTE. � The BT2 default prompt can also be changed during the above oper- ation.(SEE 5 BELOW). 5. Change BT2 default prompt to reflect configuration centre & person responsible for upload of Option 11 database. To change prompt type "X" to Set Extended Options and then press "spacebar" untill prompt "Prompt:" is displayed.Type for example "TCC/mkh" (Taunton configuration centre/Martin Kermit Hoare) in response.SEVEN characters are allowed in response, but if less re- quired terminate by pressing "spacebar".Press "spacebar" untill prompt "Reboot?:" is displayed then type "Y^T켸^P" to except change & commit to memory or "켸" to discard change & return to "BT2>" prompt. 6. To gain transparency to the Option 11 type "T",prompt "Port:" will be returned,type "1",prompt "Flow Control(Y/N):" will be returned,type "N",and "Transparency active..." should be displayed.You should now be able to log on to the Option 11!