Line side Upgrade method via the Pcmcia card To Upgrade the XA 5.7 USE = upgradeXa "127.0.0.1","itgadmin","itgadmin","/A:/","ITGPFW57.BIN" Trunk side Upgrade method via the Pcmcia card To Upgrade the ITG_TRU.O USE = upgradeXa "127.0.0.1","itgadmin","itgadmin","/A:/","ITG_TRU.O" To Upgrade the XA 5.6 USE = upgradeXa "127.0.0.1","itgadmin","itgadmin","/A:/","ITGPFW56.BIN" To Upgrade the XA 5.7 USE = upgradeXa "127.0.0.1","itgadmin","itgadmin","/A:/","ITGPFW57.BIN" To Upgrade the XA 6.7 (Strong Arm media card on the A Drive) USE = upgradeXa "127.0.0.1","itgadmin","itgadmin","/A:/","SMCFW67.BIN" To Upgrade software USE = swDownload "127.0.0.1","itgadmin","itgadmin","/A:/","IPT30118.p2" To Upgrade software USE = swDownload "127.0.0.1","itgadmin","itgadmin","/A:/","IPT30122.p2" itgHelp: Displays all of the ITG Commands i Display the current task status list. ifShow Display IP parameters. itgHelp Show complete command list. ? will also show command list. logout Exit the shell. routeAdd Add a route to the network routing table. routeShow Display the current host and network routing tables. shellPasswordSet Change the current username and password. auditShow Show audit task setting auditRebootSet Enable/Disable reboot when a task is suspended auditRebootTimeSet Set reboot time when a non-critical task is suspended auditTaskSet Force a task to be considered as a critical or non-critical task auditHistoryShow Show task monitoring history === General_Purpose Commands === ping Send ICMP echo request(s) to another host firmwareVersionShow Prints out firmware version number IPInfoShow Prints IP information itgCardShow Show card info itgChanStateShow Show State fo channels, eg. busy or idle itgMemShow Show the memory usage logPrintOff Turns off logging to the logged in tty session logPrintOn Turns on logging to the logged in tty session logFileOff Turns off logging to the syslog file logFileOn Turns on logging to the syslog file logConsoleOff Turns off logging to the console logConsoleOn Turns on logging to the console logShow Shows information about the current logging configuration numChannelsShow Prints out number of available channels resetOM Resets the operational measurement file timer serialNumShow Prints out card serial number shellPasswordSet Change the default ITG shell password swVersionShow Prints out software version tpsShow Show TPS info chkdsk chkdsk "/C:" checks the internal file system for errors chkdsk chkdsk "/C:", 1 repairs file system errors, saving damaged clusters in files chkdsk chkdsk "/C:", 2 repairs file system errors, returning damaged clusters to the free pool === File Transfer Commands === bootPFileGet Sends an updated bootptab file from MAT to ITG bootPFilePut Sends the bootptab file to the specified host configFileGet Sends an updated config.ini file form MAT to ITG logFilePut Sends the syslog file from ITG to MAT omFilePut Sends the current OM file to the specified host currOMFilePut Sends the current OM file to the specified host prevOMFilePut Sends the previous OM file to the specified host hostFileGet Transfers any file from MAT to ITG hostFilePut Transfers any file from ITG to the specified host swDownload Loads new version of software from FTP host to ITG card traceFilePut Sends the syslog file to the specified host === IP Programming Commands === clearLeader Clear the leader info in NVRAM, set the boot method to use bootp, and remove the old config files nvramLeaderClr Clears the leader bit in NVRAM, but does not erase the IP parameters in NVRAM nvramLeaderSet Sets the leader bit in NVRAM NVRClear Clears IP parameters in NVRAM NVRGWSet Sets the default gateway address in NVRAM NVRIPSet Sets the IP address in NVRAM NVRIPShow Prints the values of the IP parameters that reside in NVRAM NVRSMSet Sets the subnet mask in NVRAM setLeader Sets a leader card, including IP address, gateway, subnet mask, boot method to static, and leader bit in NVRAM tLanSpeedSet Set the TLAN ethernet speed tLanSpeedGet Get the TLAN ethernet speed tLanDuplexSet Set the TLAN ethernet duplex mode === Card Commands === cardReset Reset ITG card upgradeXa use ftp to copy a file from a host and program the 8051 with it. === DSP Commands === DSPNumShow Prints number of DSPs on ITG card DSPReset Reset the specified DSP === Patch Commands === pload Loads a patch file into DRAM pins Activation of the patch poos Deactivation of a patch in in-service state pout Removes a patch from DRAM pstat Gives summary status for loaded patches plis Gives detailed patch status for a loaded patch pnew Creates a memory patch === Misc Commands === itgAlarmTest Generates ITGXXXX test alarms itsAlarmTest Generates ITSXXXX test alarms itgPLThreshold Set the i2004 and gateway alarm packet loss threshold (units .1%) auditReboot Set autoReboot flag when audit task detect a suspended task auditShow Display the autoReboot flag lastResetReason Display the last reason the system was reset disiAll Graceful disable LTPS and VGW enaAll Enable LTPS and VGW (opposite of disiAll) pbxLinkShow Show pbx link status electShow Shows the card TPS state, current master and a list of online TPSs elmShow Shows a list of supported languages disiTPS Disable TPS service when idle enaTPS Enable TPS service (opposite of disiTPS) umsPolicyShow Display the the current upgrade policy umsUpgradeAll Upgrades all registered sets according to policy and firmware file umsUpgradeTimerShow Show Upgrade Schedule umsUpgradeTimerCancel Cancel scheduled upgrade isetShow Show general information for all registered sets isetShowByTN Show general information for all registered sets, sorted by TN isetShowByIP Show general information for all registered sets, sorted by IP isetReset Reset registered i2004 set isetResetAll Reset all registered i2004 sets isetCount Show total number of registered sets isetGet Show a list of IP phones based on a given query itgPLThreshold Set the i2004 and gateway alarm packet loss threshold (units .1%) nodePwdSet Set password for current node nodePwdShow Show node password setting on local TPS nodePwdShowMaster Show node password setting from current node master nodePwdEnable Enable node password setting nodePwdDisable Disable node password setting nodeTempPwdSet Set a temporary password for current node nodeTempPwdClear Clear the temporary password for current node clearLockout Clear Branch User Config lockout captureStart Capture PCM data to file for external playback captureFree Free Memory used by PCM data capture buffer captureStop Stop the current PCM capture captureSaveLocal Save the current PCM capture buffer to a file captureSaveRemote Save the current PCM capture buffer to a remote computer vgwShow Show information about the busy gateway channels vgwShowAll Show information about all the gateway channels vgwPLLog Toggle gateway packet loss logging on/off disiVGW Disable voice gateways when idle enaVGW Enable voice gateways service (opposite of disiVGW)